Con il nuovo kernel errori e conflitti...ACPI ma non solo ....

Problemi e discussioni inerenti al kernel e al supporto hardware in ambiente Linux
Rispondi
Ubermensch
Little John
Messaggi: 994
Iscritto il: 27 maggio 2008, 14:28

Messaggio da Ubermensch » 14 ottobre 2009, 12:37

Ragazzi con il nuovo Kernel dmesg mi restituisce una serie di errori....che devo fare???

Codice: Seleziona tutto

Linux version 2.6.31-ARCH (root@architect) (gcc version 4.4.1 (GCC) ) #1 SMP PREEMPT Thu Oct 8 11:32:00 CEST 2009
Command line: root=/dev/disk/by-uuid/1d708d9c-605f-44d4-be7b-ed04c49a62ed resume=/dev/sda5 ro 
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  Centaur CentaurHauls
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000bfed0000 (usable)
 BIOS-e820: 00000000bfed0000 - 00000000bfee1000 (ACPI NVS)
 BIOS-e820: 00000000bfee1000 - 00000000c0000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
 BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
 BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
DMI present.
last_pfn = 0x140000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-CFFFF write-protect
  D0000-DFFFF uncachable
  E0000-FFFFF write-protect
MTRR variable ranges enabled:
  0 base 0C0000000 mask FC0000000 uncachable
  1 base 000000000 mask F00000000 write-back
  2 base 100000000 mask FC0000000 write-back
  3 disabled
  4 disabled
  5 disabled
  6 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 00000000c0000000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0xbfed0 max_arch_pfn = 0x400000000
e820 update range: 0000000000001000 - 0000000000006000 (usable) ==> (reserved)
Scanning 1 areas for low memory corruption
modified physical RAM map:
 modified: 0000000000000000 - 0000000000001000 (usable)
 modified: 0000000000001000 - 0000000000006000 (reserved)
 modified: 0000000000006000 - 000000000009f800 (usable)
 modified: 000000000009f800 - 00000000000a0000 (reserved)
 modified: 00000000000e0000 - 0000000000100000 (reserved)
 modified: 0000000000100000 - 00000000bfed0000 (usable)
 modified: 00000000bfed0000 - 00000000bfee1000 (ACPI NVS)
 modified: 00000000bfee1000 - 00000000c0000000 (reserved)
 modified: 00000000e0000000 - 00000000f0000000 (reserved)
 modified: 00000000fec00000 - 00000000fec10000 (reserved)
 modified: 00000000fed00000 - 00000000fed00400 (reserved)
 modified: 00000000fed14000 - 00000000fed1a000 (reserved)
 modified: 00000000fed1c000 - 00000000fed90000 (reserved)
 modified: 00000000fee00000 - 00000000fee01000 (reserved)
 modified: 00000000ff000000 - 0000000100000000 (reserved)
 modified: 0000000100000000 - 0000000140000000 (usable)
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000bfed0000
 0000000000 - 00bfe00000 page 2M
 00bfe00000 - 00bfed0000 page 4k
kernel direct mapping tables up to bfed0000 @ 8000-d000
init_memory_mapping: 0000000100000000-0000000140000000
 0100000000 - 0140000000 page 2M
kernel direct mapping tables up to 140000000 @ b000-11000
RAMDISK: 37f23000 - 37fef5fc
ACPI: RSDP 00000000000f7ae0 00024 (v02 PTLTD )
ACPI: XSDT 00000000bfed3841 0007C (v01 ACRSYS ACRPRDCT 06040000  LTP 00000000)
ACPI: FACP 00000000bfeddc2a 000F4 (v03 INTEL  CRESTLNE 06040000 ALAN 00000001)
ACPI: DSDT 00000000bfed4db5 08E01 (v02 INTEL  CRESTLNE 06040000 MSFT 03000001)
ACPI: FACS 00000000bfee0fc0 00040
ACPI: APIC 00000000bfeddd1e 00068 (v01 INTEL  CRESTLNE 06040000 LOHR 0000005A)
ACPI: HPET 00000000bfeddd86 00038 (v01 INTEL  CRESTLNE 06040000 LOHR 0000005A)
ACPI: MCFG 00000000bfedddbe 0003C (v01 INTEL  CRESTLNE 06040000 LOHR 0000005A)
ACPI: APIC 00000000bfedddfa 00068 (v01 PTLTD  	 APIC   06040000  LTP 00000000)
ACPI: BOOT 00000000bfedde62 00028 (v01 PTLTD  $SBFTBL$ 06040000  LTP 00000001)
ACPI: SLIC 00000000bfedde8a 00176 (v01 ACRSYS ACRPRDCT 06040000 acer 00000000)
ACPI: SSDT 00000000bfed4ad8 002DD (v01 SataRe SataAhci 00001000 INTL 20050624)
ACPI: SSDT 00000000bfed3e79 0025F (v01  PmRef  Cpu0Tst 00003000 INTL 20050624)
ACPI: SSDT 00000000bfed3dd3 000A6 (v01  PmRef  Cpu1Tst 00003000 INTL 20050624)
ACPI: SSDT 00000000bfed38bd 00516 (v01  PmRef    CpuPm 00003000 INTL 20050624)
ACPI: BIOS bug: multiple APIC/MADT found, using 0
ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
ACPI: Local APIC address 0xfee00000
(8 early reservations) ==> bootmem [0000000000 - 0140000000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
  #2 [0001000000 - 00016837d0]    TEXT DATA BSS ==> [0001000000 - 00016837d0]
  #3 [0037f23000 - 0037fef5fc]          RAMDISK ==> [0037f23000 - 0037fef5fc]
  #4 [000009f800 - 0000100000]    BIOS reserved ==> [000009f800 - 0000100000]
  #5 [0001684000 - 0001684178]              BRK ==> [0001684000 - 0001684178]
  #6 [0000008000 - 000000b000]          PGTABLE ==> [0000008000 - 000000b000]
  #7 [000000b000 - 000000c000]          PGTABLE ==> [000000b000 - 000000c000]
found SMP MP-table at [ffff8800000f7b10] f7b10
 [ffffea0000000000-ffffea00045fffff] PMD -> [ffff880028600000-ffff88002bdfffff] on node 0
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  DMA32    0x00001000 -> 0x00100000
  Normal   0x00100000 -> 0x00140000
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
    0: 0x00000000 -> 0x00000001
    0: 0x00000006 -> 0x0000009f
    0: 0x00000100 -> 0x000bfed0
    0: 0x00100000 -> 0x00140000
On node 0 totalpages: 1048170
  DMA zone: 56 pages used for memmap
  DMA zone: 103 pages reserved
  DMA zone: 3835 pages, LIFO batch:0
  DMA32 zone: 14280 pages used for memmap
  DMA32 zone: 767752 pages, LIFO batch:31
  Normal zone: 3584 pages used for memmap
  Normal zone: 258560 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 0000000000001000 - 0000000000006000
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 00000000bfed0000 - 00000000bfee1000
PM: Registered nosave memory: 00000000bfee1000 - 00000000c0000000
PM: Registered nosave memory: 00000000c0000000 - 00000000e0000000
PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
PM: Registered nosave memory: 00000000fec10000 - 00000000fed00000
PM: Registered nosave memory: 00000000fed00000 - 00000000fed14000
PM: Registered nosave memory: 00000000fed14000 - 00000000fed1a000
PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
PM: Registered nosave memory: 00000000fed1c000 - 00000000fed90000
PM: Registered nosave memory: 00000000fed90000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000
PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 28 pages at ffff880028022000, static data 82400 bytes
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1030147
Kernel command line: root=/dev/disk/by-uuid/1d708d9c-605f-44d4-be7b-ed04c49a62ed resume=/dev/sda5 ro 
PID hash table entries: 4096 (order: 12, 32768 bytes)
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Initializing CPU#0
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
software IO TLB at phys 0x20000000 - 0x24000000
Memory: 4054324k/5242880k available (3628k kernel code, 1050200k absent, 137388k reserved, 1501k data, 484k init)
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
NR_IRQS:768
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 2500.254 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 5002.86 BogoMIPS (lpj=8334180)
Security Framework initialized
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring handled by SMI
using mwait in idle threads.
Performance Counters: Core2 events, Intel PMU driver.
... version:                 2
... bit width:               40
... generic counters:        2
... value mask:              000000ffffffffff
... max period:              000000007fffffff
... fixed-purpose counters:  3
... counter mask:            0000000700000003
ACPI: Core revision 20090521
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU     T9300  @ 2.50GHz stepping 06
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5002.41 BogoMIPS (lpj=8333461)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
mce: CPU supports 6 MCE banks
CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU     T9300  @ 2.50GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (10004.27 BogoMIPS).
CPU0 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 0 1
CPU1 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 1 0
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: missing confirmations, switch off interrupt mode.
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: No dock devices found.
ACPI Error (psargs-0359): [CDW1] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [_SB_.PCI0._OSC] (Node ffff88013f812b60), AE_NOT_FOUND
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0x1800-0x181f]
pci 0000:00:1a.1: reg 20 io port: [0x1820-0x183f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xf3504800-0xf3504bff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xf3500000-0xf3503fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0x1840-0x185f]
pci 0000:00:1d.1: reg 20 io port: [0x1860-0x187f]
pci 0000:00:1d.2: reg 20 io port: [0x1880-0x189f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xf3504c00-0xf3504fff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0600 (mask 003f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0068 (mask 0007)
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
pci 0000:00:1f.1: reg 20 io port: [0x18a0-0x18af]
pci 0000:00:1f.2: reg 10 io port: [0x18d8-0x18df]
pci 0000:00:1f.2: reg 14 io port: [0x18cc-0x18cf]
pci 0000:00:1f.2: reg 18 io port: [0x18d0-0x18d7]
pci 0000:00:1f.2: reg 1c io port: [0x18c8-0x18cb]
pci 0000:00:1f.2: reg 20 io port: [0x18e0-0x18ff]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xf3504000-0xf35047ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 32bit mmio: [0x000000-0x0000ff]
pci 0000:00:1f.3: reg 20 io port: [0x1c00-0x1c1f]
pci 0000:01:00.0: reg 10 32bit mmio: [0xf2000000-0xf2ffffff]
pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xf0000000-0xf1ffffff]
pci 0000:01:00.0: reg 24 io port: [0x2000-0x207f]
pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:00:01.0: bridge io port: [0x2000-0x2fff]
pci 0000:00:01.0: bridge 32bit mmio: [0xf0000000-0xf2ffffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:00:1c.0: bridge io port: [0x00-0xfff]
pci 0000:00:1c.0: bridge 32bit mmio: [0x000000-0x0fffff]
pci 0000:00:1c.0: bridge 64bit mmio pref: [0x000000-0x0fffff]
pci 0000:06:00.0: reg 10 32bit mmio: [0x000000-0x000fff]
pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:00:1c.3: bridge io port: [0x00-0xfff]
pci 0000:00:1c.3: bridge 32bit mmio: [0x000000-0x0fffff]
pci 0000:00:1c.3: bridge 64bit mmio pref: [0x000000-0x0fffff]
pci 0000:08:00.0: reg 10 64bit mmio: [0x000000-0x00ffff]
pci 0000:08:00.0: PME# supported from D3hot D3cold
pci 0000:08:00.0: PME# disabled
pci 0000:00:1c.5: bridge io port: [0x00-0xfff]
pci 0000:00:1c.5: bridge 32bit mmio: [0x000000-0x0fffff]
pci 0000:00:1c.5: bridge 64bit mmio pref: [0x000000-0x0fffff]
pci 0000:0a:09.0: reg 10 32bit mmio: [0xf3200000-0xf32007ff]
pci 0000:0a:09.0: supports D1 D2
pci 0000:0a:09.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0a:09.0: PME# disabled
pci 0000:0a:09.1: reg 10 32bit mmio: [0xf3200800-0xf32008ff]
pci 0000:0a:09.1: supports D1 D2
pci 0000:0a:09.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0a:09.1: PME# disabled
pci 0000:0a:09.2: reg 10 32bit mmio: [0xf3200c00-0xf3200cff]
pci 0000:0a:09.2: supports D1 D2
pci 0000:0a:09.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0a:09.2: PME# disabled
pci 0000:0a:09.3: reg 10 32bit mmio: [0xf3201000-0xf32010ff]
pci 0000:0a:09.3: supports D1 D2
pci 0000:0a:09.3: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0a:09.3: PME# disabled
pci 0000:0a:09.4: reg 10 32bit mmio: [0xf3201400-0xf32014ff]
pci 0000:0a:09.4: supports D1 D2
pci 0000:0a:09.4: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0a:09.4: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xf3200000-0xf32fffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.RP04._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.RP06._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PCIB._PRT]
ACPI Error (psargs-0359): [CDW1] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [_SB_.PCI0._OSC] (Node ffff88013f812b60), AE_NOT_FOUND
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 *7 11 12 14 15)
PCI: Using ACPI for IRQ routing
pci 0000:00:1c.0: BAR 13: can't allocate resource
pci 0000:00:1c.0: BAR 14: can't allocate resource
pci 0000:00:1c.0: BAR 15: can't allocate resource
pci 0000:00:1c.3: BAR 13: can't allocate resource
pci 0000:00:1c.3: BAR 14: can't allocate resource
pci 0000:00:1c.3: BAR 15: can't allocate resource
pci 0000:00:1c.5: BAR 13: can't allocate resource
pci 0000:00:1c.5: BAR 14: can't allocate resource
pci 0000:00:1c.5: BAR 15: can't allocate resource
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:01: iomem range 0xfed40000-0xfed44fff has been reserved
system 00:01: iomem range 0xfed45000-0xfed8ffff has been reserved
system 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
system 00:06: ioport range 0x680-0x69f has been reserved
system 00:06: ioport range 0x800-0x80f has been reserved
system 00:06: ioport range 0x1000-0x107f has been reserved
system 00:06: ioport range 0x1180-0x11bf has been reserved
system 00:06: ioport range 0x1640-0x164f has been reserved
system 00:06: ioport range 0xfe00-0xfe00 has been reserved
pci 0000:01:00.0: BAR 6: can't allocate mem resource [0xe0000000-0xdfffffff]
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0:   IO window: 0x2000-0x2fff
pci 0000:00:01.0:   MEM window: 0xf0000000-0xf2ffffff
pci 0000:00:01.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0:   IO window: disabled
pci 0000:00:1c.0:   MEM window: disabled
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:06
pci 0000:00:1c.3:   IO window: disabled
pci 0000:00:1c.3:   MEM window: 0xc0000000-0xc00fffff
pci 0000:00:1c.3:   PREFETCH window: disabled
pci 0000:00:1c.5: PCI bridge, secondary bus 0000:08
pci 0000:00:1c.5:   IO window: disabled
pci 0000:00:1c.5:   MEM window: 0xc0100000-0xc01fffff
pci 0000:00:1c.5:   PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0a
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: 0xf3200000-0xf32fffff
pci 0000:00:1e.0:   PREFETCH window: disabled
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.3: enabling device (0000 -> 0002)
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.5: enabling device (0000 -> 0002)
pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.5: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io:  [0x2000-0x2fff]
pci_bus 0000:01: resource 1 mem: [0xf0000000-0xf2ffffff]
pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xdfffffff]
pci_bus 0000:02: resource 0 mem: [0x0-0xfff]
pci_bus 0000:02: resource 1 mem: [0x0-0xfffff]
pci_bus 0000:02: resource 2 mem: [0x0-0xfffff]
pci_bus 0000:06: resource 0 mem: [0x0-0xfff]
pci_bus 0000:06: resource 1 mem: [0xc0000000-0xc00fffff]
pci_bus 0000:06: resource 2 mem: [0x0-0xfffff]
pci_bus 0000:08: resource 0 mem: [0x0-0xfff]
pci_bus 0000:08: resource 1 mem: [0xc0100000-0xc01fffff]
pci_bus 0000:08: resource 2 mem: [0x0-0xfffff]
pci_bus 0000:0a: resource 1 mem: [0xf3200000-0xf32fffff]
pci_bus 0000:0a: resource 3 io:  [0x00-0xffff]
pci_bus 0000:0a: resource 4 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs...
Freeing initrd memory: 817k freed
Simple Boot Flag at 0x35 set to 0x1
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1255513887.140:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 7922
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.3: irq 26 for MSI/MSI-X
pcieport-driver 0000:00:1c.3: setting latency timer to 64
pcieport-driver 0000:00:1c.5: irq 27 for MSI/MSI-X
pcieport-driver 0000:00:1c.5: setting latency timer to 64
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
registered taskstats version 1
Initalizing network drop monitor service
Freeing unused kernel memory: 484k freed
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 28 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 abar m2048@0xf3504000 port 0xf3504100 irq 28
ata2: SATA max UDMA/133 abar m2048@0xf3504000 port 0xf3504180 irq 28
ata3: SATA max UDMA/133 abar m2048@0xf3504000 port 0xf3504200 irq 28
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi3 : ata_piix
scsi4 : ata_piix
ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WP03, max UDMA/33
ata4.00: configured for UDMA/33
ata2: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ACPI Warning: _SB_.PCI0.SATA.PRT0._GTF: Return type mismatch - found Integer, expected Buffer 20090521 nspredef-940
ata1.00: _GTF unexpected object type 0x1
ata1.00: ATA-8: Hitachi HTS542525K9SA00, BBFOC31P, max UDMA/133
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: _GTF unexpected object type 0x1
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54252 BBFO PQ: 0 ANSI: 5
scsi 3:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T20N  WP03 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
PM: Starting manual resume from disk
EXT4-fs (sda1): barriers enabled
kjournald2 starting: pid 562, dev sda1:8, commit interval 5 seconds
EXT4-fs (sda1): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sda1): mounted filesystem with ordered data mode
rtc_cmos 00:07: RTC can wake from S4
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
udev: starting version 146
ACPI: SSDT 00000000bfed4754 002BC (v01  PmRef  Cpu0Ist 00003000 INTL 20050624)
ACPI: SSDT 00000000bfed40d8 005F7 (v01  PmRef  Cpu0Cst 00003001 INTL 20050624)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
Marking TSC unstable due to TSC halts in idle
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor LNXCPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 00000000bfed4a10 000C8 (v01  PmRef  Cpu1Ist 00003000 INTL 20050624)
ACPI: SSDT 00000000bfed46cf 00085 (v01  PmRef  Cpu1Cst 00003000 INTL 20050624)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
processor LNXCPU:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
ACPI: I/O resource 0000:00:1f.3 [0x1c00-0x1c1f] conflicts with ACPI region SMBI [0x1c00-0x1c0f]
ACPI: Device needs an ACPI driver
i801_smbus: probe of 0000:00:1f.3 failed with error -16
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf3504800
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf3504c00
input: PC Speaker as /devices/platform/pcspkr/input/input2
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
ACPI: WMI: Mapper loaded
acer-wmi: Acer Laptop ACPI-WMI Extras
acer-wmi: Brightness must be controlled by generic video driver
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
ACPI: Lid Switch [LID]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
ACPI: Power Button [PWRB]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input6
ACPI: Sleep Button [SLPB]
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 3:0:0:0: Attached scsi generic sg1 type 5
acerhdf: Acer Aspire One Fan driver, v.0.5.13
acerhdf: no Aspire One hardware found
usb 1-2: new high speed USB device using ehci_hcd and address 2
ACPI: AC Adapter [ACAD] (on-line)
usb 1-2: configuration #1 chosen from 1 choice
usb 5-2: new low speed USB device using uhci_hcd and address 2
Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1e0b1, caps: 0xc04751/0xe0500f
usb 5-2: configuration #1 chosen from 1 choice
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio3/input/input7
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
fuse init (API version 7.12)
ricoh-mmc: Ricoh MMC Controller disabling driver
ricoh-mmc: Copyright(c) Philip Langdale
ricoh-mmc: Ricoh MMC controller found at 0000:0a:09.2 [1180:0843] (rev 12)
ricoh-mmc: Controller is now disabled.
cfg80211: Calling CRDA to update world regulatory domain
Synaptics Touchpad, model: 1, fw: 6.5, id: 0x81a0b1, caps: 0xa04711/0xa04000
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  185.18.36  Fri Aug 14 17:35:21 PDT 2009
Clocksource tsc unstable (delta = -250703138 ns)
ACPI: Battery Slot [BAT1] (battery present)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pci 0000:0a:09.1: SDHCI controller found [1180:0822] (rev 22)
sdhci-pci 0000:0a:09.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
sdhci-pci 0000:0a:09.1: Will use DMA mode even though HW doesn't fully claim to support it.
Registered led device: mmc0::
mmc0: SDHCI controller on PCI [0000:0a:09.1] using DMA
tg3.c:v3.99 (April 20, 2009)
tg3 0000:08:00.0: enabling device (0000 -> 0002)
tg3 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
tg3 0000:08:00.0: setting latency timer to 64
usbcore: registered new interface driver hiddev
tg3 0000:08:00.0: wake-up capability disabled by ACPI
tg3 0000:08:00.0: PME# disabled
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device Acer CrystalEye webcam (064e:a101)
input: MosArt Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input9
generic-usb 0003:13EE:0003.0001: input,hidraw0: USB HID v1.10 Mouse [MosArt Optical Mouse] on usb-0000:00:1d.0-2/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
ohci1394 0000:0a:09.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (27 C)
input: Acer CrystalEye webcam as /devices/pci0000:00/0000:00:1a.7/usb1/1-2/1-2:1.0/input/input10
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
loop: module loaded
eth0: Tigon3 [partno(BCM95787m) rev b002] (PCI Express) MAC address 00:1e:68:3d:cc:30
eth0: attached PHY is 5787 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
lirc_dev: IR Remote Control driver registered, major 61 
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]  MMIO=[f3200000-f32007ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
lirc_wpc8769l: Found WEC1020 device via ACPI.
lirc_dev: lirc_register_driver: sample_rate: 0
lirc_wpc8769l: Driver loaded.
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input11
iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
iwl3945: Copyright(c) 2003-2009 Intel Corporation
iwl3945 0000:06:00.0: enabling device (0000 -> 0002)
iwl3945 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
iwl3945 0000:06:00.0: setting latency timer to 64
iwl3945 0000:06:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
iwl3945 0000:06:00.0: Detected Intel Wireless WiFi Link 3945ABG
iwl3945 0000:06:00.0: irq 29 for MSI/MSI-X
phy0: Selected rate control algorithm 'iwl-3945-rs'
acpi device:04: registered as cooling_device2
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/device:03/input/input12
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
EXT4-fs (sda1): internal journal on sda1:8
Adding 1502036k swap on /dev/sda5.  Priority:-1 extents:1 across:1502036k 
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00241b00de62cf00]
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
tg3 0000:08:00.0: wake-up capability disabled by ACPI
tg3 0000:08:00.0: PME# disabled
tg3 0000:08:00.0: irq 30 for MSI/MSI-X
iwl3945 0000:06:00.0: firmware: requesting iwlwifi-3945-2.ucode
iwl3945 0000:06:00.0: loaded firmware version 15.32.2.9
Registered led device: iwl-phy0::radio
Registered led device: iwl-phy0::assoc
Registered led device: iwl-phy0::RX
Registered led device: iwl-phy0::TX
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
wlan0: direct probe to AP 00:04:ed:5d:bb:7f try 1
wlan0 direct probe responded
wlan0: authenticate with AP 00:04:ed:5d:bb:7f
wlan0: authenticated
wlan0: associate with AP 00:04:ed:5d:bb:7f
wlan0: RX AssocResp from 00:04:ed:5d:bb:7f (capab=0x421 status=0 aid=2)
wlan0: associated
tg3: eth0: Link is down.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
tg3: eth0: Link is down.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
CE: hpet increasing min_delta_ns to 15000 nsec
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present

adriano
Arciere Provetto
Messaggi: 538
Iscritto il: 20 luglio 2008, 13:45
Contatta:

Messaggio da adriano » 14 ottobre 2009, 13:08

se ti riferisci a questo

Codice: Seleziona tutto

pci 0000:00:1c.5: BAR 14: can't allocate resource
non puoi far nulla se non dowgradare il kernel. Comunque l'errore è innocuo quindi ignoralo. Io l'ho avuto costantemente dal kernel 2.6.21 al 2.6.26...

aleph
Robin Hood
Messaggi: 1530
Iscritto il: 12 febbraio 2008, 16:30
Contatta:

Messaggio da aleph » 14 ottobre 2009, 13:20

vale sempre la regola 'se funziona tutto, non fare niente' . . e può anche darsi che siano semplicemente warnings su problemi preesistenti e precedentemente ignorati . . per dire anch'io ho un paio di messaggi di warning acpi, ma funziona tutto più che bene quindi non me ne preoccupo . .
ImmagineOutside of a dog, computers are a man's best friend, inside a dog it's too dark to type.

Ubermensch
Little John
Messaggi: 994
Iscritto il: 27 maggio 2008, 14:28

Messaggio da Ubermensch » 14 ottobre 2009, 13:53

Dunque mi riferivo a questo in particolare :

Codice: Seleziona tutto

ACPI: I/O resource 0000:00:1f.3 [0x1c00-0x1c1f] conflicts with ACPI region SMBI [0x1c00-0x1c0f]
e questo :

Codice: Seleziona tutto

i801_smbus: probe of 0000:00:1f.3 failed with error -16
:rolleyes:

perfectcircle
Arciere
Messaggi: 314
Iscritto il: 29 agosto 2007, 1:06
Località: viterbo

Messaggio da perfectcircle » 14 ottobre 2009, 13:58

ho anch'io quei due errori,ma funziona tutto mi pare.....

Ubermensch
Little John
Messaggi: 994
Iscritto il: 27 maggio 2008, 14:28

Messaggio da Ubermensch » 14 ottobre 2009, 14:12

A volte ci si può non accorgere di alcune cose....si apparentemente funziona tutto......:rolleyes:

aleph
Robin Hood
Messaggi: 1530
Iscritto il: 12 febbraio 2008, 16:30
Contatta:

Messaggio da aleph » 14 ottobre 2009, 19:10

da un'oscura ml trovata via google
ACPI: I/O resource 0000:00:1f.3 [0x1c00-0x1c1f] conflicts with ACPI region SMBI [0x1c00-0x1c0f] ACPI: Device needs an ACPI driver

Your ACPI tables use the smbus controller themselves, so using a native Linux driver could potentially result in race conditions and bizarre failures. If you're not trying to use your smbus controller directly then it's not really an issue.
ImmagineOutside of a dog, computers are a man's best friend, inside a dog it's too dark to type.

Ubermensch
Little John
Messaggi: 994
Iscritto il: 27 maggio 2008, 14:28

Messaggio da Ubermensch » 14 ottobre 2009, 19:47

Ah beh allora se non è problema... meglio così...:cool:

Avatar utente
ugaciaka
Little John
Messaggi: 1345
Iscritto il: 6 luglio 2008, 9:06
Località: Belluno
Contatta:

Messaggio da ugaciaka » 15 ottobre 2009, 15:55

Ubermensch ha scritto:Dunque mi riferivo a questo in particolare :

Codice: Seleziona tutto

ACPI: I/O resource 0000:00:1f.3 [0x1c00-0x1c1f] conflicts with ACPI region SMBI [0x1c00-0x1c0f]
e questo :

Codice: Seleziona tutto

i801_smbus: probe of 0000:00:1f.3 failed with error -16
:rolleyes:
prova a blacklistare i801_smbus

Su rc.conf metti !i801_smbus su MODULES oppure su /etc/modprobe.d/blacklist aggiungici la riga

Codice: Seleziona tutto

blacklist i801_smbus
Tanto il modulo da quanto ho capito viene caricato ma non può lavorare perché se lo tiene ACPI quindi blacklistalo così non sta lì a lamentarsi col kernel che non può fare niente,

Oppure togli acpi ma non mi pare una genialata (acpi=off su grub...)
non ho mai comprato su ebay, i macbook non mi piacciono, non ho bisogno di facebook né myspace né secondlife
non sono un nerd né lamer né troll né geek né cracker né hacker

Ubermensch
Little John
Messaggi: 994
Iscritto il: 27 maggio 2008, 14:28

Messaggio da Ubermensch » 15 ottobre 2009, 19:45

No non posso togliere acpi anche perchè trattasi di un laptop ....mi limito a blacklistare il modulo. Grazie!!! :cool:

EDIT

I messaggi rimangono purtroppo.....:rolleyes:
Ultima modifica di Ubermensch il 15 ottobre 2009, 19:53, modificato 1 volta in totale.

Rispondi